And S darn near had a heart attack. Option one is a whole lot less frou-frou next to that ball of frou, no? Problem one was fixed with a cheap-o ceiling cap and some wire cutters. It's an even less expensive (downright cheap) way to hardwire a plug-in light than we used when we hardwired the CB2 Eden pendent. Lucky for you, S agreed to let me photograph every single little step so you can do the same. And by "agreed to let me" I really mean that he agreed to repeat every single step for me to photograph so I could provide a quick tutorial since the first time around he closed the door to the room and surprised me with a fully installed light fifteen minutes later.
Let me start by saying we don't have grounding wires everywhere in our house, so we usually ground to the metal junction box or a grounding screw, it varies by fixture. Similarly this particular pendant does not have a ground line since the fat side of the plug is the grounding side. We're not going to simultaneously stand in a puddle of water while propped on a stool and touch the light fixture. We suggest you don't either. We also have a properly wired wall switch, which means that in the "off" position there is no power reaching the fixture, so as long as we change the bulbs with the switch "off" we should be ok.
For all legal purposes this is an educational tutorial and we won't take any responsibility if you hack up a light and make a mistake along the way. We're comfortable with electricity and have our work double-checked, if you are not comfortable please proceed at your own risk, follow the original plan we had when we originally hard-wired the CB2 Eden pendant, or hire an electrician. If you want to use a grounded fixture, we suggest this inexpensive one from Westinghouse.
So here we go, this is our version of how to hard wire a plug-in light. First up, shut off the breaker to the circuit you're working on. Please don't skip this 'cause you think you can manage not to touch a live wire. If you're so good that you can manage not to shock yourself while working with live wire I can
guarantee you're not reading this post. Or you at least stopped reading after I stopped waxing poetic about our dog.
Second, get all your supplies ready. Here we have the cheap-o ceiling fixture cap that we bought in a clearance bin at Ikea (no name, sorry!) but I'm sure you can find them at Home Depot or Lowe's. In addition to the wire cutters here, we also used our wire stripper, a box cutter/utility knife and a couple of wire nuts. We did not use the metal plate at the bottom right. So really, this photo is kind of useless. Sorry.
1. Cut the plug off your cord and slip on the cheap-o ceiling cap and nut making sure that the cut wires are facing the "up" side of the cap. If you can't find a cap with a screw like this you could just use a $1.97 round cover plate with a hole drilled in the center. It was our plan before I found this cap for $2.99 and totally splurged on two.
2. Have helper hold the light to the ceiling and mark the length on the cord where it meets the cap, all while helper says, "please don't put a picture of my face on the blog."
3. Cut off all but about a foot of cord past your mark (unless you think you might want the pendant longer some day and think you have room to coil extra cord in your ceiling box).
4. Using your utility knife carefully cut down the center of the cord for about two inches, trying to just barely cut the outer coating of the cord.
5. Pull back the cut to reveal the inside wires and insulation.
6. These next few steps are important. Hold the wires in one hand and the cut portion of covering and insulation in the other.
7. Pull to essentially rip down more of the covering until you're past the point where you first inserted the utility knife.
8. This is to make sure that you didn't nick what might later become a live wire with your box cutter. Look, we did here even though S was extremely careful when he made the first cut with the box cutter.
9. Snip off the outer covering and insulation and then cut the inner wires just below where you nicked the line (if you nicked the line).
10. Strip about an inch off the end of the wires.
11. Move the cheap-o ceiling cover down towards the pendant and out of the way.
12. Slide on the ceiling bracket that your old fixture was hanging from. (If you didn't have an old fixture go and buy one of these brackets to fit the box in your ceiling. They're kind of universal. I say "kind of" because we've found that nothing ever fits a 1941 house perfectly.) Tie a knot just above the bracket so that when you snug the cheap-o ceiling cap up to the whole assembly to test things out, the point that you marked lines up with the bottom of the cap hanging into the room. (If you're using a cover plate then have your mark line up with the hole you drilled.)
13. Take your pliers and pull the knot super tight. DO NOT use sharp pliers or anything else that could cut the cord here.
14. Repeat to make a tight, thick double knot. Make more knots if you have to, you just don't want the wire to be able to slip through the metal bracket.
15. Move the cheap-o cap down the line to get it out of your way, hop up on your step stool and wire the hot and neutral wires to your ceiling fixture (white to neutral, black to live), twist and secure with wire nuts.
16. Gently coil any excess wire into the ceiling box and then take that bracket that you tied the knot near and screw it into the ceiling box.
17. Snug your cheap-o cap up to the ceiling and secure its nut, or if you're using a ceiling cap with a hole in the center then screw that in place.
18. Pop in a CFL light bulb and run down to the basement to flip the breaker back on. Run back upstairs, flip on the switch and admire your handy work.
 |
| Add caption |
19. Touch up the paint on the ceiling next time you have your paintbrush out.
So there you go, funky but not too frou-frou. That's how we hardwire Ikea lights or hard wire CB2 pendants (which we may be doing again soon, stay tuned), or hardwire any other plug in hanging ceiling light. Let us know in the comments section if you have a good source for a cheap-o ceiling cap and we'll update this tutorial.
